'HONDA' Cut-to-Length Slitting and Shearing Line
‘HONDA’ Shearing Line with Side Trimmer and 2 x 6-High Finish Levellers
Make: Honda Metal Industries
Type: ‘Cut-to-Length’ Shearing with Side Trimmer and 2 x 6-High Finish Levellers
Year of manufacture: 1989
Application: Cut and process steel coils into precise widths and lengths while ensuring high-quality surface finishes and material handling efficiency
Equipment weight (estimated): approx. 250 tons
Line length: approx. 74 meters
Processed material: AISI 300 & 400 series stainless steel in coil
70 kgs/mm2 > tensile strength > 53 kgs kgs/mm2
52.5 kgs/mm2 > yield points > 21 kgs kgs/mm2
Strip width: 500 – 1320 mm
Strip thickness: 0.3 – 3.5 mm
Coil weight: max. 20,000 kg
Coil inside diameter: 610 mm
Coil outside diameter: 1,000 – 7,500 mm
Line speed (coiling): min. 30 mpm max. (2.0 – 3.5 mm)
max. 60 mpm max. (0.3 – 2.0 mm)
Line travelling direction: Left to right (left hand line)
Mechanical equipment list:
– Paper Winder
– P.O.R. with Out-Board, Hold Down Roll & CPC
– Pinch Roll Leveller with Opener
– Hydraulic Shear
– No.1 Loop Table with Apron Guide
– Side Trimmer with Side Guide
– Scrap Baller & Scrap Winder
– No.2 Loop Table with Apron Guide
– Heavy Type 6 High Finish Leveller
– Hot Air Heater
– Feeder Unit with measuring Device
– Vinyl Sheet Coater
– Paper Feeder
– Static Electro Motor
– Trans Cyclic Motor
– Run-Out Conveyor & Reject Piler with Conveyor
E&A equipment and motor list:
– PLC Control DCS5000 (RELIANCE, 2020)
– Drive (RELIANCE, 2020) x 5
– DC Motor 75KW x 2
– DC Motor 45KW x 1
– DC Motor 37KW x 1
– DC Motor 15KW x 1
– DC Motor 11KW x 1
– AC Motor x 84
– Transformer 1000KVA x 1
– EPC (NIRECO)
This lot is part of a combination lot: A Complete Stainless Steel Cold Rolling Facility(Combination)
Download Documents
Sale Specific Terms
These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.
Terms and conditions
The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.
The buyer's attention is in particular drawn to the provisions of clause 8 and the buyer should note that:
All equipment is sold 'as is, where is' (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment. It is the buyer's responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment. All sales are final – no exceptions. Sales may be subject to a buyer's premium (defined below), the rate of which will vary from sale to sale. All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place.
DEFINITIONS AND INTERPRETATION
The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;
