2x 'Production Machinery Co.' Annealing and Pickling Lines
‘PRODUCTION MACHINERY CO’ Continuous Annealing & Pickling Line No. 1
Make: Production Machinery Corporation Mentor Ohio
Type: Hot and Cold Rolled Stainless Steel Strip Continuous Annealing and Pickling Line
Year of manufacture: 1989
Revamping / upgrades: New Burners (2022)
Mothballed since: Ceased production in September 2023
Application: Continuous annealing to relieve internal stresses and improve ductility, followed by pickling to remove surface oxides and impurities, resulting in a clean, smooth, and high-quality surface finish
Equipment weight (estimated): approx. 400 tons
Line overall length: approx. 220 meters
Material: 300 and 400 series hot and cold rolled stainless strip
Yield strength: max. 140 kg/mm2 cold rolled material
max. 50 kg/mm2 annealed material
max. 50 kg/mm2 hot rolled material
Shear strength: max. 100 kg/mm2 cold rolled material
max. 60 kg/mm2 annealed material
max. 50 kg/mm2 hot rolled material
Strip width: 600 – 1,320 mm
Strip thickness: 0.3 – 3.5 mm cold rolled
3 – 6 mm hot rolled
Coil weight: max. 20,000 kg
Coil inside diameter: 610 mm entry and exit
Coil outside diameter: max. 2,200 mm incl. paper
Line Speed: 6 to 40 mpm
Leader strip: max. 4.0 mm thickness
4 – 10 m lenght
Mechanical equipment list:
– No.1&2 Entry Coil Storage Saddle
– No.1&2 Entry Coil Car
– No.1&2 P.O.R.
– No.1&2 Hold Down Rolls
– No.1&2 Flatteners
– No.1, 2 Side Guide
– No.1, 2 Entry Shear
– No.1, 2 Leader Strip
– Discharge Tables
– Entry Strip Support Table
– No.1 Pinch Roll
– No.2 Pinch Roll
– Welder
– Degreasing Section
– No.1 Bridle
– No.1 Steering Roll
– Entry Loop Car System
– No.2 Steering Roll
– No.2 Bridle
– Tension Meter
– Annealing Furnace, Cooling Section
– Dryer, No.3 Steering Roll
– No.3 Bridle, Shot Blast
– No.1 Deflector Roll
– Shot Blast Rinse
– Electrolytic Pickling
– No.1 Brush Scrubber
– Post Treatment Tank
– No.2 Brush Scrubber
– Cascade Rinse
– Fume Exhaust System
– Hot Air Dryer
– Reclaim Water Tank, Pump System
E&A equipment and motor list:
– PLC Controls AUTOMAX (RELIANCE, 2008)
– PLC Annealing Furnace CENTUM VP R5 (YOKOGAWA, 2011)
– Drive (RELIANCE, 2008) x 17
– Automax Rack x 24 (RELIANCE)
– DC Motor 55 KW x 2
– DC Motor 37.5 KW x 3
– DC Motor 22.5 KW x 2
– DC Motor 22 KW x 2
– DC Motor 19 KW x 2
– DC Motor 18.5 KW x 3
– DC Motor 15 KW x 4
– DC Motor 11 KW x 5
– DC Motor 7.5 KW x 4
– DC Motor 5.5 KW x 3
– DC Motor 0.75 KW x 4
– Transformer 1250 KVA x 3
– Transformer 1000 KVA x 4
– Transformer 750 KVA x 2
– Transformer 500 KVA x 3
– Transformer 300 KVA x 3
– Transformer 150 KVA x 4
– Transformer 100 KVA x 4
– Transformer 75 KVA x 6
– Transformer 50 KVA x 4, 5KVA x 2
This lot is part of a combination lot: A Complete Stainless Steel Cold Rolling Facility(Combination)
Download Documents
Sale Specific Terms
These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.
Terms and conditions
The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.
The buyer's attention is in particular drawn to the provisions of clause 8 and the buyer should note that:
All equipment is sold 'as is, where is' (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment. It is the buyer's responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment. All sales are final – no exceptions. Sales may be subject to a buyer's premium (defined below), the rate of which will vary from sale to sale. All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place.
DEFINITIONS AND INTERPRETATION
The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;
