'HONDA' Slitting / Recoiling Line
‘HONDA’ Slitting Line
Make: Honda Metal Industries
Type: DC-controlled Slitting / Recoiling Line for Edge Cutting
Year of manufacture: 1989
Application: Precision slitting and recoiling of metal strips
Equipment weight (estimated): approx. 250 tons
Line overall length: approx. 35 meters
Line traveling direction: Right to left
Processed material: AISI 300 & 400 series stainless steel in coil
70 kgs/mm2 > tensile strength > 53 kgs kgs/mm2
52.5 kgs/mm2 > yield points > 21 kgs kgs/mm2
Strip width: 500 – 1320 mm entry
min. 45 mm exit
Strip thickness: 0.3 – 3.5 mm
Coil weight: max. 20,000 kg
Coil inside diameter: 610 mm entry
508 mm exit
Coil outside diameter: 2,000 mm
Cutting system: Drive cut and pull cut
Line speed (coiling): 80 m/min max. (0.3 – 2.0 mm)
40 m/min max. (2.0 – 3.5 mm)
Utilities: Electric power: 60Hz 3Ø 440V ±10%
Plant air: 5 kgs/cm2
Mechanical equipment list:
– Paper Winder
– Coil Stocker
– Entry Cradle Coil Car
– Pay-off Reel with Out Board and Hold-Down Roll & CPC
– Pinch Roll Leveller with Opener
– Hydraulic Shear
– No. 1 Loop Table with Apron Guide
– Side Guide Pinch
– Slitter
– Slitter Spare Stand & Changing Car
– Scrap Baller and Scrap Winder
– No. 2 Loop Table with Apron Guide
– Tension Pad with Pinch Roll
– Deflector Roll
– Tension Reel with Out Board
– Exit Cradle Coil Car and Arm Unloader
– Paper Feeder
– Hydraulic Equipment
– Pneumatic Equipment
– Electrical Equipment
E&A equipment and motor list:
– PLC Control S7 (SIEMENS, 2012)
– Drive S7 (SIEMENS, 2012) x 4
– DC Motor 75 KW x 1
– DC Motor 45 KW x 1
– DC Motor 30 KW x 1
– DC Motor 15 KW x 1
– AC Motor x 20
– Transformer 153 KVA x 1
This lot is part of a combination lot: A Complete Stainless Steel Cold Rolling Facility(Combination)
Download Documents
Sale Specific Terms
These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.
Terms and conditions
The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.
The buyer's attention is in particular drawn to the provisions of clause 8 and the buyer should note that:
All equipment is sold 'as is, where is' (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment. It is the buyer's responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment. All sales are final – no exceptions. Sales may be subject to a buyer's premium (defined below), the rate of which will vary from sale to sale. All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place.
DEFINITIONS AND INTERPRETATION
The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;
