'PRODUCTION MACHINERY CO' Grinding and Polishing Line

Lot No. 7A
Details
Terms & Conditions
Contact Us
Lot No. 7A

'PRODUCTION MACHINERY CO' Grinding and Polishing Line

Year: 1989
Make: 'PRODUCTION MACHINERY CO'

‘PRODUCTION MACHINERY CO’ Grinding and Polishing Line

Make: Production Machinery Corporation Mentor Ohio
Type: Grinding and Polishing Line
Year of manufacture: 1989
Revamping / upgrades: New hydraulics in 2022
Mothballed since: Ceased production in September 2023
Application: Achieve smooth, high-quality surfaces by removing imperfections, enhancing corrosion resistance, and preparing the material for further processing
Equipment weight (estimated): approx. 250 tons
Line overall length: approx. 43 meters
Line direction: Left to right (left hand line)                         
Material: Hot and Cold Rolled Stainless Steel
                AISI 300 and 400 Series
               (Annealed and Pickled)
Yield strength: 56 kg/mm2                                                   
Shear strength: 75 kg/mm2
Strip width: 600 – 1,320 mm
Strip thickness: 0.5 – 3.5 mm cold rolled
                            3 – 6 mm hot rolled        
Coil weight: max. 20,000 kg
Coil inside diameter: 610 mm
Coil outside diameter: max. 2,200 mm incl. paper
                                       min. 1,000 mm
Line Speed: 5 – 10 mpm grinding (low)
                   10 – 20 mpm polishing (high)
Threading speed: 10 mpm
Strip tension: max. 27,000 kg low speed
                       min. 13,500 kg high speed
Grinding stations: 1 bottom side grinder
                               4 top side grinders (2 active, 2 future)
                                                                                     
Mechanical equipment list:

–            Entry Coil Saddle
–            Entry Coil Car
–            Paper Winder
–            P.O. Reel
–            Hold Down Roll
–            Coil Peeler and Threading
–            Table
–            Entry Edge Control
–            Flattener
–            Entry Shear
–            Spot Welder(Gun Type)
–            Entry Pinch Roll
–            Polisher
–            Drag Wipe and Deflector Roll
–            Degreasing Section
–            Exit Shear
–            Exit Deflector Roll
–            Exit Edege Guide
–            Tension Reel
–            Paper Winder
–            Exit Coil Car
–            Exit Coil Saddle
–            Line Strip Support Table

E&A equipment and motor list:

–            PLC Control DCS5000 (RELIANCE, 2019)
–            Drive (RELIANCE, 2019) x 3
–            DCS Rack × 2 (RELIANCE)
–            P.O.R., RECOILER DC Motor 55KW 500 VDC x 2
–            AC Motor x 44
–            Transformer 1500KVA x 1
–            Transformer 500KVA x 1
–            Transformer 300KVA x 1
–            Transformer 200KVA x 1
–            Spot Welder (THE TAYLOR WINFIELD CORP.)
–            EPC (NORTH AMERICAN) 

This lot is part of a combination lot: A Complete Stainless Steel Cold Rolling Facility(Combination)

Download Documents

Sale Specific Terms

These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.

Terms and conditions

The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.

The buyer's attention is in particular drawn to the provisions of clause 8 and the buyer should note that:

All equipment is sold 'as is, where is' (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment. It is the buyer's responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment. All sales are final – no exceptions. Sales may be subject to a buyer's premium (defined below), the rate of which will vary from sale to sale. All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place.

DEFINITIONS AND INTERPRETATION

The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;

WhatsApp
Contact Us From