SMS Mannesmann Demag Sack Hot Plate Leveler (1990)
Year of Mfg. 1990; Continuously upgraded
Cassette type leveler
Max Plate Width: 3.900 mm
Max Leveling Pressure: 30.000kN
Min Plate Thickness: 4 mm (pre-leveling range)
8 mm (hot leveling range)
Max Plate Thickness: 100 mm (hot leveling), exception 200 mm
Plate Length: 3 – 10 Meter
Plate Temperatures: 250 – 1.000º Celcius
C. (Stainless Steel): 1.50º C
Stainless Steel Leveling range-diagram: see table 01.03
Max pressure depending on plate width: see table 01.04 – 01.05
Max travel of top adjustments: see table 01.06 – 01.09
Roll diameter x length (for all rolls) diameter: 285 mm x 4.100 mm
No. of leveling rolls: 11 (all powered)
Division of all leveling rolls: 300 mm
Support of the top rolls: 5 x 6
Support of the bottom rolls: 4 x 6
Support of the exit rolls: 2 x 3
Max opening between the leveling rolls: 300 mm
Max. distance between the columns: 4.100 mm
Leveling speed: 0 to 46,5/93 M/min. (approx.)
Adjustment speed of leveling rolls: 0 to 20 mm/sec. (approx.)
Adjustment speed of exit rolls: v to 1,0 mm/sec.
(4) Main drive motors: 278 kW, each
Plate thickness ranges: 8-25/100/200 mm
Max Leveling Speed: 1,5 M/sec.
Max Leveling Force: 30.000 kN
11 Straightening Rolls: 5 top and 6 bottom
Roll diameter length: 285 mm x 4.100 mm
Main adjustment: 4 Hydraulic Cylinders.
Special adjustment (hydraulic): Cambering of Straightening Rolls, Tipping, Weighing
Controls: ABB (upgraded after 2010)
Two change cassettes (one located at bay 23)
Equipped with:
(4) Hydraulic Cylinders for cambering (bending) of the rolls.
Flatness and Temperature Measuring and Unit “NOKRA”, situated at the entry of the Leveler
Lifting Beam for lifting Rolls
Download Documents
Sale Specific Terms
These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.
Terms and conditions
The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.
The buyer's attention is in particular drawn to the provisions of clause 8 and the buyer should note that:
All equipment is sold 'as is, where is' (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment. It is the buyer's responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment. All sales are final – no exceptions. Sales may be subject to a buyer's premium (defined below), the rate of which will vary from sale to sale. All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place.
DEFINITIONS AND INTERPRETATION
The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;
