Details
Documents
Terms & Conditions
Contact Us
Lot No. 2

Hot Strip Mill

Consists of:
Single Slab Reheat Furnace
• Type: Walking Beam
• Manufacturer: Davy
• Capacity: 150 t/h
• Inside Refractory Width: 8,35 m
• Effective Length: 32,6 m
• Slab Thickness: 160 mm
• Slab Maximum Length: 7,5 m
• Primary Fuel: mixed BFG and COG
• Alternate Fuel: N°6 Fuel Oil
• Commissioned in 1995
 
Water Descalers
• Primary descaler at slab reheat furnace run out table
• Front and back 3 Hi Rougher Mill descalers.
• Finishing Mill descaler at run-in table.
 
Water Descaling Pumps
• Manufacturer: Union Pump Company
• N° of Pumps: Two (one operating, one stand by.)
• Power: 5.000 HP (3.730 kW)
• Pump Speed: 4.500 rpm
• Discharge Pressure: 127 barg (1.840 psig)
 
Rougher Mill
• Type: 3 Hi, one stand 22" x 34" x 100" Reversing Mill
• Manufactured by Blaw-Knox in 1923.
• Main Motor : Synchronous type
• Main Motor Power: 6000 HP
• Motor Speed: 250 rpm
• Maximum Rolling Force: 700 t
• Maximum Edger Force: 100 t
• Edger Motor Power: 300 HP (224 kW)
• Transfer Bar Speed: 2,9 m/s
 
Crop Shear
• Drum Type Rotary Crop Shear
• Manufacturer: United
• Maximum Transfer Bar Section: 32 x 1575 mm at 940 °C, 0,4%C Carbon Steel
• Maximum Transfer Bar Speed: 2.5 m/s
 
Finishing Mill
• Type: 4 Hi 6 Stands
• Mechanical Manufacturer: United
• Electrical Manufacturer: General Electric
• Roll Barrel: 1.727 mm (68”)
• Work Rolls Diameter: 699 mm (27,5”)
• Back-Up Roll Diameter: 1.380 mm (54”)
• Maximum Rolling Force Stands 1 to 4: 2.400 t
• Maximum Rolling Force Stand 5: 2.000 t
• Maximum Rolling Force Stand 6: 1.600 t
• Electromechanical Screw down Stands 1 to 4
• Electromechanical Screw down & hydraulic capsules in Stands 5 & 6.
• 40 t per chock work roll bending per stand.
• Main Drives Stands 1 and 2: 6.000 HP (4.476 kW)
• Main Drives Stands 3 to 5: 5.000 HP (3.730 kW)
• Main Drive Stan 6: 4.000 HP (2.984 kW)
• All main drives are DC with thyristor speed control.
• Maximum Finishing Speed: 830 m/min
• Two X-Ray Gages
• Commissioned in 1970 (Stands 3 to 6) and revamped in 1995 (Adding Stands 1 & 2)
 
Laminar Cooling
• Seven Cooling Sections                    
• Three Control Zones
• Total Water Flow: 5.270 m³/h
• Upper Face Cooling: 4.100 m³/h
• Bottom Face Cooling: 1.170 m³/h
• Water Pressure: 2,5 barg
 
Single Downcoiler
• Two Wrapper Rolls pneumatically activated.
• Maximum Coil Width: 1.575 mm (62”)
• Maximum Coil Weight: 20 t
• Maximum Coil Diameter: 1.727 mm (68”)
• Mandrel Diameter: 724 mm (28.5“)
• Strip Thickness: 1,8 to 12,7 mm             

Download Documents

Sale Specific Terms

These terms are the sale specific terms as mentioned in article 1.1.18 of the terms and conditions below. This sale is a private treaty sale, as described in article 1.1.14 of the terms and conditions below. When a bid is accepted, a sales agreement will be made to be signed by the buyer and the seller. In the sales agreement, the buyer and seller will state the terms for payment and removal, that may deviate from the terms and conditions below.

Terms and conditions

The following terms and conditions ("terms") are the terms on which hilco industrial acquisitions bv (“hilco”), at jan van goyenkade 10-2, 1075 hp amsterdam, the netherlands, registered under the following number 60720700 at the chamber of commerce in amsterdam, sells equipment (defined below) at auctions (defined below) or by means of private treaty sales (defined below) and supersedes all other terms and conditions relating to the subject matter of these terms. These terms are the terms subject to which hilco shall, either on its own behalf or as agent for the vendor (defined below), sell equipment to a buyer (defined below) by way of auction or private treaty sale.

The buyer’s attention is in particular drawn to the provisions of clause 8 and the buyer should note that:

All equipment is sold ‘as is, where is’ (with all faults, imperfections and defects) No guarantees and/or warranties are provided by hilco in respect of any equipment It is the buyer’s responsibility to inspect equipment prior to bidding on such equipment or making an offer in respect of such equipment All sales are final – no exceptions Sales may be subject to a buyer’s premium (defined below), the rate of which will vary from sale to sale All auctions (defined below) are subject to the conditions, valid in the country, where the auction takes place DEFINITIONS AND INTERPRETATION .1. The following words and phrases used in these Terms shall have the following meanings, except where the context clearly requires otherwise: "Advertising Material" means brochures, pamphlets, advertisements and any other marketing material (in both electronic and printed format) used by HILCO to market and promote the Auctions and/or any Private Treaty Sale;

SALE CONTACT


Mara Valencia

mvalencia@hilcoglobal.com   

+31 (0)20 470 0989     

whatsapp
Contact Us From